ZNYX ZX4300P
Layer 2 Unmanaged Switch for PICMG 2.16 CompactPCI Packet Switching Backplane Chassis
Main Features:
- 24 port 10/100 Mbps Ethernet Switch
- Layer 2 unmanaged switching
- Use in::
PICMG 2.16 fabric slots, PICMG 2.16 node slots, CompactPCI peripheral slots
- # Two optional Rear Transition Boards
- Designed for NEBS Level 3 compliance
- Non-blocking line-rate performance
- 802.3x and back-pressure flow control
- HotSwap and CarrierClass
- Works with any host OS or CPU
Product Overview:
The ZX4300P CompactPCI Ethernet 10/100 Mbps switch is the most cost-effective and flexible solution to Embedded CarrierClass Layer 2 switching requirements.
ZNYX Networks' ZX4300P is the first switch designed to support the PICMG 2.16 specification for a CompactPCI Packet Switching Backplane (CPSB), but it can also be deployed in a standard CompactPCI chassis by using an optional 24-port rear transition board (RTB). There are three configurations where the ZX4300P may be employed:
- 1. When installed in the fabric slot of a CPSB chassis, the ZX4300P includes support for the extended CPSB specification, routing all 24 10/100 ports to the backplane. It also supports the typical 19 node standard CPSB chassis, and, with the addition of the ZXRTB05 RTB, routes the remaining 5 ports to rear-panel RJ-45 connectors. This allows the systems architect to easily add other chassis to the switched backplane fabric.
- 2. The ZX4300P may also be installed in a node slot of a CPSB chassis and paired with a ZXRTB24 rear transition board. This setup will provide 22 (not 24) 10/100 ports for rear panel I/O. In this configuration, the ZX4300P may also communicate at 10/100 Mbps over the CPSB backplane via port 23 to an intelligent, managed CPSB switch, such as a ZX4500P, located in Fabric slot A, and via port 07 to a ZX4500P switch in Fabric slot B.
- 3. In a third configuration, the ZX4300P is installed in a standard CompactPCI chassis peripheral slot (without an H.110 bus), and configured with a ZXRTB24 RTB to provide rear panel I/O for all 24 10/100 ports. This permits stand-alone operation of a single, or multiple, layer 2 switches in a CompactPCI chassis to gain the advantages of HotSwap and redundant power supplies offered by some chassis.
In either chassis, the ZX4300P's HotSwap and instant reconfiguration features allow rapid installation in a live system and a mean-time-to-repair of mere seconds.
By using the latest switch silicon, the ZX4300P features non-blocking line-rate switching, 802.3x and back-pressure flow control. Like the ZNYX Networks OpenArchitect switches, the ZX4300P is designed for NEBS Level 3 compliance and may be used with any host operating system or host CPU, including Sun SPARC, Intel x86, and Motorola PowerPC.
The ZX4300P best satisfies the demand for a high quality, high density, low cost, and high performance Ethernet switch. It enables system architects to accelerate development of their next-generation CPSB products and achieve first-to-market deployment.
Hardware:
- ZX4300P
24-port 10/100 Ethernet switch for CPSB fabric or node slots, and Std. CompactPCI peripheral slots
- ZXRTB05
5-port, single-slot width, Rear Transition Board (RTB) for CPSB fabric slots
- ZXRTB24
24-port, two-slot width, RTB for standard CompactPCI peripheral (24 active rear ports) or CPSB node slots (22 active rear ports)